Many patients who come to ARTÉ by Dr. M have already tried a single-machine tightening treatment elsewhere and felt something was missing.
Someone might do focused ultrasound for sagging jowls and get a firmer jawline three months later, yet the skin on their cheeks still looks thin and crepey. Another patient might book radiofrequency to smooth fine lines, only to find that their heavy lower face still pulls downward.
Most clinic promotions in Singapore present non-surgical lifting as a single-device choice. The catch is that your face does not age in a single layer. As time passes, the deep muscle fascia (SMAS) stretches, the collagen bed in the dermis thins out, and elastin near the surface breaks down all at once.
Expecting one machine to fix all three layers rarely works. At ARTÉ by Dr. M, Dr. Michelle and Dr. Alfred design combination treatment plans that pair Ultherapy Prime, XERF, and Sofwave so each layer of tissue gets the specific energy it responds to best.
Three layers of facial ageing, three different treatments
1. The deep foundation (4.5mm SMAS): Ultherapy Prime
The Superficial Musculoaponeurotic System (SMAS) is a fibrous sheet of muscle and collagen that wraps around your lower face and connects to the neck muscles. It acts like an internal sling holding up your facial fat pads. When the SMAS loosens, gravity pulls the lower face down into jowls, marionette folds, and a double chin.
Surface lasers and shallow radiofrequency cannot reach down to 4.5mm. Dr. Michelle and Dr. Alfred uses Ultherapy Prime guided by a live high-definition ultrasound screen to place focused ultrasound energy directly into the SMAS and 3.0mm deep dermis. Contracting that deep layer pulls the lower face back up and sharpens the jawbone border.
2. Skin thickness and bounce (1.0mm to 3.5mm dermis): XERF
Tightening the deep SMAS layer lifts the framework of your face, but it does not thicken thin skin. If pinching your cheek feels soft or spongy rather than firm, the issue is collagen loss in the reticular dermis.
To rebuild that thickness, Dr. Michelle and Dr. Alfred use XERF by Cynosure Lutronic. Operating on two monopolar radiofrequency settings (6.78 MHz and 2 MHz) with continuous surface cooling, XERF warms the entire volume of the dermis to between 40°C and 45°C. That three-dimensional heat compacts the collagen network, shrinks enlarged pores, and brings back firm, springy skin across the cheeks and jawline.
3. Surface lines and delicate zones (1.5mm mid-dermis): Sofwave
Right beneath the surface sits the upper collagen bed, which controls how smooth your skin looks in bright light. When elastin breaks down here, you see fine accordion lines around the mouth, horizontal neck creases, and heavy eyebrows.
Sofwave fires seven parallel ultrasound beams at a fixed depth of 1.5mm while its built-in cooling plate (Sofcool) chills the top layer of skin. Because the energy stops at 1.5mm and never touches deeper facial fat, it smooths fine lines, firms crepey neck skin, and lifts the outer brow arch with zero downtime and zero risk of hollowing out lean cheeks.
How Dr. Michelle and Dr. Alfred sequence combination plans
Every patient comes in with different priorities and a different amount of time before their year-end events. Here are three ways Dr. Michelle and Dr. Alfred commonly stage these treatments:
1. The 10-week holiday reset (Ultherapy Prime + XERF + Sofwave)
If you have moderate sagging along the jawbone plus thinner, crepey skin on your cheeks and neck, starting in October gives you enough runway to treat all three layers:
- October (Week 0): Full-face Ultherapy Prime (600 to 800 lines) to start remodeling the deep SMAS layer, which takes two to three months to peak.
- November (Week 4): XERF monopolar RF to thicken the dermis and tighten pores.
- Early December (Week 8): Sofwave across the brow and neck for a final surface lift two weeks before your parties begin.
2. The same-day dual lift (Ultherapy Prime + Sofwave)
If you have a packed schedule and want a single appointment that addresses both deep sagging and surface lines, Dr. Michelle and Dr. Alfred can perform Ultherapy Prime at 4.5mm along the lower face and under the chin, followed in the same 90-minute visit by Sofwave at 1.5mm across the cheeks, brow, and neck. Because the two machines target different depths, the heat zones do not overlap.
3. The 4-week contour and smooth plan (XERF + Sofwave)
If you have a naturally slender face and want a tighter jawline and smoother skin without deep ultrasound soreness, pairing XERF with a follow-up Sofwave session two weeks later firms the full dermis and smooths fine lines in time for December dinners.
Want a plan built around your face shape?
Book a consultation with Dr. Michelle or Dr. Alfred at ARTÉ by Dr. M to have your facial structure and skin thickness assessed in person.
Why facial mapping matters when combining devices
Combining multiple high-energy machines takes careful planning. Firing deep ultrasound into naturally hollow temples or lean cheeks can break down fat pads where you want to keep volume, while firing lines without following your natural ligament angles will not lift heavy jowls.
At ARTÉ by Dr. M, Dr. Michelle and Dr. Alfred start every visit by watching how your tissue shifts when you smile, talk, and rest. They map out which fat pockets need to be left alone, which zones need 4.5mm SMAS lifting versus 1.5mm surface firming, and the exact line and pulse counts needed so your face looks rested and natural rather than tight.
Recovery, pricing in Singapore, and what to bring to your consultation
Because Ultherapy Prime, Sofwave, and XERF all work beneath the top layer of skin without breaking the surface, recovery is easy to manage around a busy work calendar. Any mild warmth or pinkness fades within an hour or two of your appointment, and you can wear sunscreen and makeup the same day. If your plan includes Ultherapy Prime along the jawbone, your jawline may feel slightly tender when washing your face for three to five days.
Compared to a surgical facelift in Singapore which typically costs $18,000 to $30,000, requires general anaesthesia, and involves three to four weeks of bruising and swelling a multi-layer non-surgical plan builds your own collagen with no incisions and no time off work.
When you come in to see Dr. Michelle or Dr. Alfred, bring the dates of any major December dinners, weddings, or trips so they can time your sessions properly, and let them know if you have had any Botox, dermal fillers, or thread lifts in the past few months so they can plan around those areas safely.
Frequently asked questions
Can I still get skin boosters or Botox?
Yes. Energy devices rebuild the deeper collagen framework, and light skin boosters or Botox can be added two to four weeks later to hydrate the surface or relax expression lines.
To plan a multi-layer treatment around your year-end calendar, book a consultation with Dr. Michelle or Dr. Alfred at ARTÉ by Dr. M.


